Eken t01a

From linux-sunxi.org
Jump to: navigation, search
Eken t01a
T01a front.jpg
Manufacturer Eken
Dimensions widthmm x breadthmm x heightmm
Release Date 2012
Website Device Product Page
Specifications
SoC A10 @ 1.008Ghz
DRAM 384MiB DDR3 @ xxxMHz
NAND 4GB
Power DC 5V @ 3A, 3700mAh 3.7V Li-Ion battery
Features
LCD 800x480px (7" 16:9)
Touchscreen 2-finger capacitive (Manufacturer device)
Video mini HDMI
Audio 3.5mm headphone plug, HDMI, internal speaker, internal microphone
Network WiFi 802.11 b/g/n (Manufacturer device)
Storage µSD
USB 1 USB2.0 Host, 1 miniUSB2.0
Camera 0.3MP (640x480) front

This page needs to be properly filled according to the New Device Howto and the New Device Page guide.

Identification

Surprinsingly, on the back of the device there's no more than a Made in China label with a few regulatory logos.

The PCB has the following silkscreened on it:

T01A_V6
2012.02.06

In android, under Settings->About Tablet, you will find:

  • Model Number: T01A
  • Build Number: crane_evb-eng 4.0.3 IML74K 20120320 test-keys

Sunxi support

Current status

Give a brief overview of the current status of support under sunxi here.

Images

Optional. Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be removed.

HW-Pack

Optional. Add MANUFACTURER DEVICE sunxi HW-pack specifics here. When empty, this section can be removed.

BSP

Optional. Add MANUFACTURER DEVICE sunxi BSP specifics here. When empty, this section can be removed.

Manual build

You can build things for yourself by following our Manual build howto and by choosing from the configurations available below.

U-Boot

Sunxi/Legacy U-Boot

Only useful for A10/A10s/A13 and A20 based devices. Remove this section otherwise.

Use the MANUFACTURER_DEVICE build target.

Mainline U-Boot

Use the MANUFACTURER_DEVICE build target.

Linux Kernel

Sunxi/Legacy Kernel

Only useful for A10/A10s/A13 and A20 based devices. Remove this section otherwise.

Use the MANUFACTURER_DEVICE.fex file.

Mainline kernel

Use the FAMILY-CHIP-DEVICE.dtb device-tree binary.

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

FEL mode is triggered by the reset button. It's located up, left of the volume rocker.

In a non powered state, press the reset button and the power on button, this will make the device boot up to FEL mode.

Device specific topic

If there are no further device specific topics to add, remove these sections.

...

Adding a serial port (voids warranty)

DEVICE UART pads

This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning.

Device disassembly

Opening this tablet requires removing two screws on the back. Now the device is only hold together by about ten plastic tabs. Grab the back cover from the right side with the ports, nudge a finger between the usb port and the back cover, try nudge your nails between the sides, the trick is making the back cover to bend to the outside to not put strain on the tabs.

Locating the UART

UART is located as tests pads near the A10 SoC.In some models, it is extremely easy to see which test pads need to be soldered to with a soldermask describing what signal they are carrying (see Connecting RS232 to T01a down bellow).

Pictures

Also known as

Supersonic SC-75MID

See also

Connecting RS232 to T01a


Manufacturer images

Optional. Add non-sunxi images in this section.