Xunlong Orange Pi One Plus
|Xunlong Orange Pi One Plus|
|Dimensions||68mm x 48mm|
|Release Date||December 2017|
|Website||Device Product Page|
|SoC||H6 @ 1,8 Ghz|
|DRAM||1GiB LPDDR3 @ xxxMHz|
|Power||DC 5V @ 3A|
|Video||HDMI (Type 2.0A - full)|
|Audio||HDMI, on-board microphone|
|Network||10/100/1000Mbps Ethernet (Realtek RTL8211)|
|USB||1 USB2.0 Host, 1 USB2.0 OTG|
The Orange Pi One Plus is an upgrade from the previous Orange Pi One. It uses the new Allwinner H6 SoC. In comparison to Orange Pi One, this board has Quad Core Arm Cortex-A53 cpu. The SoC also has 4k capabilities at 60fps due to it's Mali T720 GPU.
In comparison to DDR3 RAM present in most SBCs, the One Plus uses 1GiB of LPDDR3 RAM. The board has 1 USB 2.0 port, Gigabit Ethernet, Pi Compatible GPIO header, OTG, etc.
The One Plus has a black-colored pcb, different from it's older brother.
On the top of the device, the following is printed:
Orange Pi ONE PLUS
The PCB has the following silkscreened on it:
Some boards have the following instead:
In android, under Settings->About Tablet, you will find:
- Model Number: molly
- Build Number: petrel_fvd_p1-eng 7.0 NRD91N 20180110 test-keys
Give a brief overview of the current status of support under sunxi here.
Optional. Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be removed.
Optional. Add MANUFACTURER DEVICE sunxi HW-pack specifics here. When empty, this section can be removed.
Optional. Add MANUFACTURER DEVICE sunxi BSP specifics here. When empty, this section can be removed.
You can build things for yourself by following our Manual build howto and by choosing from the configurations available below.
Use the MANUFACTURER_DEVICE build target.
Use the orangepi_one_plus_defconfig (supported since v2018.09) build target.
Use the orangepi_one_plus.fex file. This was extracted from the android sdcard image.
Use the sun50i-h6-orangepi-one-plus.dtb device-tree binary.
Tips, Tricks, Caveats
Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.
The dts in mainline kernel still doesn't enable the Ethernet device (At 5.2). You need to patch it, you can use the the following patch to get it to work and to also always keep the same mac address.
Booting without an SD card automagically enters FEL mode.
./sunxi-fel version AWUSBFEX soc=00001728(H6) 00000001 ver=0001 44 08 scratchpad=00027e00 00000000 00000000
The H6 UBOOT pin is routed to test-point TP28 on the PCB.
Device specific topic
If there are no further device specific topics to add, remove these sections.
Adding a serial port
This device has a three pin UART header as shown in the picture. On the underside of the board, TX, RX, and GND are marked. Wires should be attached as described Here
Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.
Also known as
There are currently no known rebadged devices. Update this section if you know otherwise.
- AXP805 Datasheet: File:AXP805 Datasheet V1.0 en.pdf
- H6 Datasheet: File:Allwinner H6 V200 Datasheet V1.1.pdf
- H6 User Manual: File:Allwinner H6 V200 User Manual V1.1.pdf
- Schematics 2.0: File:OrangePi OnePlus Schematics v2.0.pdf
Optional. Add non-sunxi images in this section.