Onda V989 Air

From linux-sunxi.org
Jump to: navigation, search
Onda V989 Air
Onda V989 Air
Manufacturer Onda
Dimensions 241mm x 169mm x 7.9mm
Release Date February 2015
Website V989 Air Product Page
Specifications
SoC A83T @ 2.0Ghz
DRAM 2GiB DDR3 @ 456MHz
NAND 16GB, 32GB
Power DC 5V @ 2.5A, 8000mAh 3.7V Li-Ion battery
Features
LCD WidthxHeight (9.7" 1536:2048)
Touchscreen 10-finger capacitive (Silead GSL1680)
Video No video ports
Audio 3.5mm headphone plug, internal speaker, internal microphone
Network WiFi 802.11 b/g/n (Realtek 8723bs)
Storage µSD
USB 1 MicroUSB port
Camera 1.9MP (1600x1200) front, 0.3MP (640x480) rear

Contents

Identification

On the back of the device, the following is printed:

ONDA
V989 AIR

The PCB has the following silkscreened on it:

currently unknown

In android, under Settings->About Tablet, you will find:

  • Model Number: V989 Air Core8
  • Build Number: A83T_N978_N9781L2BC_1501088.20150527
  • Kernel version: Linux version 3.4.39 ([email protected]) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02))

Sunxi support

Needs a lot of work.

Current status

No Uboot defconfig at this moment.

No defconfig in linux-sunxi project.

A83T kernel sources were released April, 17 2015 Github

Images

No sunxi images availible at this moment. See Manufacturer images

HW-Pack

No HW-pack availible.

BSP

No BSP availible.

Manual build

  • For building U-Boot, use the onda_v989_air_defconfig target, which will soon be added.
  • The .fex file soon could be found in sunxi-boards as onda_v989_air.fex

Everything else is the same as the manual build howto.

Mainline U-Boot

If there is mainline U-Boot support, add this section.

For building mainline U-Boot, use the MANUFACTURER_DEVICE target.

Don't forget to add
[[Category:Mainline_U-Boot]]
at the bottom of the page.

Mainline kernel

If there is mainline kernel support, add this section.

Use the FAMILY-CHIP-DEVICE.dtb device-tree file for the mainline kernel.

Don't forget to add
[[Category:Mainline_Kernel]]
at the bottom of the page.

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

The something button triggers FEL mode.

Adding a serial port (voids warranty)

DEVICE UART pads

This section explains how to attach a serial port to the device. Make sure it refers to our UART howto. For a development board, you can just mention how to find the header with the pins and include a picture, and you can remove the warranty voiding warning.

Device disassembly

If necessary, provide a short description of how to open the device. Perhaps explain how the pins can be most easily popped. If pins do need to be popped, mention the Plastic tool howto.

Locating the UART

Describe how to find the RX,TX,GND signals here, and mention the UART howto.

Pictures

Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.

See also

Topic on Onda Forums

Manufacturer images

LiveSuit/OndaSuit/PhoenixSuit image (android version 4.4.4) Yandex Disk

Personal tools
Namespaces

Variants
Actions
Navigation
Tools