|Dimensions||widthmm x breadthmm x heightmm|
|Release Date||February 2015|
|SoC||A33 @ XGhz|
|DRAM||512MiB DDR3 @ 456MHz|
|Power||DC 5V @ 2A, 2500mAh 3.7V Li-Ion battery|
|LCD||1024x600 (7 " 16:9)|
|Touchscreen||5-finger capacitive (Silead GSL1680)|
|Audio||3.5mm headphone plug, internal speaker, internal microphone|
|Network||WiFi 802.11 b/g/n (Realtek Semiconductor RTL8703AS), Bluetooth (Realtek Semiconductor RTL8703AS)|
|USB||1 USB2.0 OTG|
|Camera||??.?MP (????x????) front, ??.?MP (????x????) rear|
On the back of the device, the following is printed:
NeuTab Model: N7 Pro
The PCB has the following silkscreened on it:
In android, under Settings->About Tablet, you will find:
- Model Number: N7Pro
- Build Number: 723Q6.A33.KK44.V2.31.150610.wsvga.rtl87x3xsvq0
Give a brief overview of the current status of support under sunxi here. If there is mainline support for either U-Boot or kernel, mention this too, but add the extra sections below.
Add MANUFACTURER DEVICE specific sunxi ROM images here. E.g. a livesuit image or some other linux image which uses linux-sunxi code. Do not put non-sunxi images here, they should live under See also. If no sunxi based images are available, this section can be left blank.
Add MANUFACTURER DEVICE HW-pack specifics here. This section can be left blank.
Add MANUFACTURER DEVICE BSP specifics here. This section can be left blank.
- For building U-Boot, use the MANUFACTURER_DEVICE target.
- The .fex file can be found in sunxi-boards as MANUFACTURER_DEVICE.fex
Everything else is the same as the manual build howto.
If there is mainline U-Boot support, add this section.
For building mainline U-Boot, use the MANUFACTURER_DEVICE target.Don't forget to add
[[Category:Mainline_U-Boot]]at the bottom of the page.
If there is mainline kernel support, add this section.
Use the FAMILY-CHIP-DEVICE.dtb device-tree file for the mainline kernel.Don't forget to add
[[Category:Mainline_Kernel]]at the bottom of the page.
Tips, Tricks, Caveats
Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.
Through serial console
This method will NOT initialize boot1. For more information on the various ways to enter FEL mode, see the FEL page.
- Power off the device
- Start a serial terminal program (
screen /dev/ttyUSB0 115200for instance)
- In the serial terminal, hold down the 2 key
- Power on the device
The device should eventually print out the following over serial:
HELLO! BOOT0 is starting! boot0 version : 3.1.0 reg_addr 0x01f00100 =0x00000000 reg_addr 0x01f00104 =0x00000000 reg_addr 0x01f00108 =0x00000000 reg_addr 0x01f0010c =0x00000000 reg_addr 0x01f00110 =0x00000000 reg_addr 0x01f00114 =0x00000000 eraly jump fel
FEL version example
$ ./fel version AWUSBFEX soc=00001667(A33) 00000001 ver=0001 44 08 scratchpad=00007e00 00000000 00000000
This device has root access enabled by default. This means that dumping things like
script.bin from NAND is as easy as:
adbon a PC, enable USB debugging on the tablet, and connect the tablet to the PC via USB
adb pull /dev/block/nanda ./nanda.imgfrom the PC to dump an image of
nandato the PC's working directory
- Power off the device
- Hold down the vol+ button
- Power on the device
- Release the vol+ button when recovery starts
Boot log from serial port
NOTE: this log is from a device that has had its battery removed.
HELLO! BOOT0 is starting! boot0 version : 3.1.0 reg_addr 0x01f00100 =0x00000000 reg_addr 0x01f00104 =0x000000cf reg_addr 0x01f00108 =0x00000000 reg_addr 0x01f0010c =0xf1f18000 reg_addr 0x01f00110 =0x00000000 reg_addr 0x01f00114 =0x00000000 DRAM DRIVE INFO: V1.4 DRAM CLK =456 MHZ DRAM simple test OK. dram size =512 sum=0xe1d09ca5 src_sum=0xe1d09ca5 Ready to disable icache. Jump to secend Boot. [ 0.220] U-Boot 2011.09-rc1 (Nov 26 2014 - 15:14:37) Allwinner Technology [ 0.228]version: 2.1.0 [ 0.304]pmbus: ready [ 0.307]PMU: AXP221 [ 0.309]PMU: AXP22x found [ 0.313]PMU: dcdc3 1200 [ 0.316]PMU: pll1 1008 Mhz,PLL6=600 Mhz AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz set power on vol to default dcdc1_vol = 3000 dcdc2_vol = 1260 dcdc3_vol = 1200 dcdc4_vol = 0 dcdc5_vol = 1600 aldo2_vol = 2500 aldo3_vol = 3000 find power_sply to end no battery, limit to dc fel key old mode run key detect no key found no key input dram_para_set start dram_para_set end [ 0.364]DRAM: 512 MiB relocation Offset is: 15b11000 smcl's set manager is NULL workmode = 0 [ 0.563]NAND: NAND_UbootInit NAND_UbootInit start NB1 : enter NAND_LogicInit uboot:physical version: 2 1b 20140616 1640 nand io drivering: 2863311530 nand : get id_number_ctl fail, 1 uboot:nand info: a714dead ffff4a42 318c 40704 5 nand : get CapacityLevel fail, 5fb9cec5 not burn nand partition table! NB1 : nftl num: 2 init nftl: 0 NB1 : NAND_LogicInit ok, result = 0x0 [ 0.872]sunxi flash init ok out of usb burn from boot: not enough energy In: serial Out: serial Err: serial --------fastboot partitions-------- -total partitions:10- -name- -start- -size- bootloader : 1000000 2000000 env : 3000000 1000000 boot : 4000000 1000000 system : 5000000 30000000 misc : 35000000 1000000 recovery : 36000000 2000000 cache : 38000000 20000000 metadata : 58000000 1000000 private : 59000000 1000000 UDISK : 5a000000 0 ----------------------------------- base bootcmd=run setargs_nand boot_normal bootcmd set setargs_nand key 0 recovery key high 5, low 3 cant find fstbt value misc partition found misc_message->command = 0 to be run cmd=run setargs_nand boot_normal mount part name bootloader cant open script.bin, maybe it is not exist WORK_MODE_BOOT board_status_probe [ 0.979]key trigger sunxi_bmp_logo_display screen_id =0, screen_width =1024, screen_height =600 [ 1.109]Hit any key to stop autoboot: 0 read boot or recovery all [ 1.605]sunxi flash read :offset 4000000, 12891315 bytes OK no signature [ 1.614]ready to boot para err in disp_ioctl, cmd = 0xa,screen id = 1 [ 1.621][mmc]: MMC Device 2 not found [ 1.625][mmc]: mmc not find,so not exit NAND_UbootExit NB1 : NAND_LogicExit nand release dma:0 [ 1.629] Starting kernel ... <4
Adding a serial port (voids warranty)
The non-chip/connector side of the board has a number of test pads on it. Solder headers or wires to the pins below the large ground pad on the right side of the board (as seen with the USB port, power port, and power button facing upwards). For more information, please reference the UART howto. Note: the UART pins are shared with the µSD (MicroSD) card pins, so please do not have a MicroSD card inserted when attempting to debug this device with a UART.
Also known as
List rebadged devices here.
Add some nice to have links here. This includes related devices, and external links.
Optional. Add non-sunxi images in this section.