Beelink GS1

From linux-sunxi.org
Jump to: navigation, search
Beelink GS1
Device front.jpg
Manufacturer Shenzhen AZW Technology
Dimensions 100mm x 100mm x 17mm
Specifications
SoC H6 @ XGhz
DRAM 2GiB LPDDR3 @744 MHz, SpecTek SM512M32V01MD2LPF-107 or 3GiB LPDDR3
NAND 16GB (eMMC 5.0) Toshiba THGBMBG7D2KBAIL, or 32GB (eMMC 5.0)
Power DC 5V @ 2A,
Features
Video HDMI (Type A - full)
Audio HDMI, SPDIF,
Network WiFi 802.11 b/g/n/ac (Fn-Link 6222B-PRB), 10/100/1000Mbps Ethernet (Realtek RTL8211E)
Storage µSD
USB 1 USB2.0 Host, 1 USB3.0 HOST

This page needs to be properly filled according to the New Device Howto and the New Device Page guide.

If a device is special, then feel free to provide a terse description of what makes this device so special. But terse, no novels, no marketing blurb.

Contents

Identification

On the bottom of the device, the following is printed:

Model:Beelink GS1

The PCB has the following silkscreened on it:

beelink
GS1
Ver:2.0

In android, under Settings->About Tablet, you will find:

  • Model Number: Beelink GS1
  • Build Number: 102NO

Sunxi support

Current status

Give a brief overview of the current status of support under sunxi here.

Manual build

You can build things for yourself by following our Manual build howto and by choosing from the configurations available below.

U-Boot

Sunxi/Legacy U-Boot

Use the MANUFACTURER_DEVICE build target.

Mainline U-Boot

Planned for 2019.07 U-boot sunxi Git

Linux Kernel

Sunxi/Legacy Kernel

Use the beelink_gs1.fex file.

Mainline kernel

Planned for 5.2 : https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux.git/commit/?h=sunxi/for-next&id=089bee8dd119ba084dee6b17a2e1a53df4f30193

Tips, Tricks, Caveats

Add MANUFACTURER DEVICE specific tips, tricks, Caveats and nice to have changes here.

FEL mode

The button on the bottom of the PCB triggers FEL mode (to be confirmed). It is reachable through a small hole in the bottom plastic cover.

Device specific topic

If there are no further device specific topics to add, remove these sections.

...

Adding a serial port (voids warranty)

DEVICE UART pads

The GS1 UART runs at 3.3V levels, so you need a level converter (e.g. MAX3323) to connect the board to a regular serial port. Alternatively, a USB-to-UART adapter with 3.3V levels will also work.

Device disassembly

The case is clipped together using plastic tabs on all four sides. Please see the Plastic tool howto for details of opening cases like these. The PCB is held in place by three small Philips-head screws. Make sure to remove the µSD card before taking out the PCB.

Locating the UART

The UART (3.3V levels) is available on four solder holes (2mm spacing) next to the eMMC chip slot. Soldering in a header will void the warranty.

With the square pad as pin 1 the pinout is as follows confirmed using USB-UART adapter:

  • Pin 1: GND
  • Pin 2: RxD
  • Pin 3: TxD
  • Pin 4: ???

Pictures

Take some pictures of your device, upload them, and add them here. DO NOT UPLOAD PICTURES WHICH YOU PLUCKED OFF THE INTERNET.

Also known as

There are currently no known rebadged devices. Update this section if you know otherwise.

See also

Manufacturer images

Optional. Add non-sunxi images in this section.

Personal tools
Namespaces

Variants
Actions
Navigation
Tools